Skip to main content
PrintSignals
Elegoo OrangeStorm Giga

Elegoo OrangeStorm Giga

WAIT

Past the brand's typical replacement window. A new model is more likely than not. Firmware and support remain active.

Signals last verified: 17 July 2026

Signals: Lifecycle · Firmware · Support · Spare parts. What we track

Note: Elegoo is still supporting the Giga through dual/quad printhead expansion, so a successor does not look imminent, but no guarantees.

Where to buy

Official SiteFilament2Print

Specifications

Build volume
800x800x1000 mm
Build size class
Massive - Appliance / Small Fridge
Price
Base: €2,749
Enclosure
Open frame
Chamber control
None
Materials
PLA · PETG · PHA · PVB · TPU · TPE · TPC · PEBA
Support materials
—
Bowden extruder
—
Max hotend temp
300°C
Max bed temp
100°C
Max chamber temp
—
Nozzle material
Brass
Hardened nozzle
—
Nozzle count
1
Max filament inputs
1
True multi-material
—
Tool change
Single Nozzle Pause Swap

Ownership

Experience level
Tinkerer
Assembly
Extended Build
Auto bed leveling
Assisted
Auto Z offset
—
Auto first layer
—
Filament runout sensor
Yes
Spaghetti detection
—
Error guidance
Generic
Warranty
24 months
Warranty extension
Not available
Spare parts
Minimal
Firmware version
V2.3.2.7

Unlockable capabilities

With hardened nozzle upgrade:
Abrasive materials

Real-world performance

Who this is for

This is not a first machine. Between the Klipper firmware, the frequent difficult maintenance, the high failure rate, and errors you diagnose yourself, a beginner would spend more time fighting it than printing. The right owner is an experienced maker or a home hobbyist who specifically needs a very large build volume, wants the speed reviewers praise, and treats tuning and calibration as part of the hobby rather than a chore. On capability the ceiling is clear: warp-stable materials plus flexibles, no ABS or ASA without an enclosure, abrasives only after a hardened-nozzle upgrade, and multi-color that means standing at the machine to swap filament by hand. For a prosumer eyeing it as a production tool, be honest about the risk. Reliability is rated a concern, official spare parts are minimal, and support responds after problems appear, which is a lot to stake a paid project on. And for everyone, the timing hangs over the decision. A successor is overdue, so buying now risks watching a new model or a lower price land shortly after. The call: unless you need this exact volume today and can absorb the tinkering, hold off, watch for a successor announcement or a price drop, and buy into a better window.

PrintSignals Review

Elegoo OrangeStorm Giga Review

Written by AI from manufacturer specifications and the aggregated consensus of

PrintSignals does not test printers hands-on. How we do this

Assessment

The OrangeStorm Giga is a very large open-frame printer, roughly 800mm on each side of the bed, aimed squarely at experienced users who want to make big parts and are comfortable running a Klipper-based machine. The reason PrintSignals rates it a WAIT is timing, not quality. Elegoo replaces models on a short cycle, averaging about 1.2 years per model, and this one is already past that window, which makes a successor announcement more likely than not. Firmware is still being maintained, with an update inside the last 90 days, so the machine is not abandoned. But between the strong chance of a new model, room for further price drops, and stock clearing out, buying today means paying close to full price right before the purchase window is likely to improve. The second thing to weigh is reliability: reviewers rate print failures and hardware issues as more frequent than expected for this class, and that is a real running cost, not a footnote. If you need the volume now and you accept the tinkering, it is a capable machine. If you can wait, waiting is the stronger play.

Build and print volume

The whole point of this printer is the build envelope. At 800 x 800 x 1000 mm it is closer to a small appliance than a desktop machine, and it lets you print things most FDM printers can only approach by splitting into pieces and gluing. Full-size functional parts, large single-piece prototypes, and props that would otherwise need seams all fit in one job. Reviewers consistently rate build and material quality as good, and they also rate real-world speed as significantly faster than typical FDM printers in its class, which matters a lot when a single print can fill a volume this size. What the hardware does not give you is thermal containment. It is an open frame, so it sits exposed to whatever the room is doing, and that shapes the material story more than the size does. Color changes run through a single nozzle with a manual pause-and-swap, so multi-color work is hands-on: you unload and reload filament at each change point yourself, and Elegoo rates that workflow as medium efficiency. It is a multi-color method, not true multi-material, and cross-contamination through the shared nozzle limits how reliably you can mix materials in one print.

Material capability

The dependable range is PLA, PETG, PHA, and PVB, and reviewers rate material handling across that range as good in practice. The hotend reaches 300°C and the bed 100°C, but the open frame is the real ceiling here: without an enclosure to hold heat, you are limited to warp-stable filaments, which is why ABS and ASA are not in the supported range on this machine. The direct drive extruder is a genuine plus for flexibles. TPU is the most accessible of them, and the hardware also handles TPE, TPC, and PEBA, though the tuning required climbs with each step. Two conditions to keep in mind before you count on any of this. The stock nozzle is brass and not hardened, so abrasive materials need a hardened-nozzle upgrade first. And supported does not mean automatic, especially at this size: reviewers note moderate stringing that expects retraction tuning, and large parts on an open frame stay sensitive to a stable ambient temperature. The capability is real, but it rewards dialing in.

Setup and ownership

This is a tinkerer's machine, and the signals are consistent about it. The firmware is Klipper-based and only lightly abstracted, so tuning, calibration, and debugging are part of normal ownership rather than rare events. It ships in sections and takes roughly 45 minutes to two hours to build, and some mechanical familiarity helps. There is a wrinkle worth checking before you buy: the printer comes as either a pre-assembled unit or a self-assembly kit, and everything described here reflects the pre-assembled version. Reviewers rate the kit build as involved but accessible to beginners, so confirm exactly which one you are ordering. Day to day, expect frequent maintenance that reviewers rate as difficult, sometimes needing significant disassembly, plus recalibration more often than is typical for the class. The print failure rate is high, which costs filament and time. It runs very loud, so a shared room or a noise-sensitive space is out. WiFi reliability is poor enough that reviewers fall back to USB or LAN, there is no built-in camera for remote monitoring, and errors surface as generic text or raw firmware messages with no structured code system, so you diagnose issues yourself. Automation is limited to assisted bed leveling and filament runout detection. You are tied to Elegoo Slicer, an Orca-based open-source tool that reviewers rate as adequate, and Orca itself is accepted. At around €2,750 for the printer alone, reviewers still call it good value for the volume and speed you get, provided you know what you are signing up to run.

Support and longevity

Support is a mixed picture. The core channels exist, and observed support is positive but limited in scope. Coverage is uneven across warranty handling, parts availability, and how well issues actually get resolved, and the pattern is reactive: this manufacturer tends to address hardware problems after they surface rather than heading them off. Spare parts are the sharper concern. Very few items are listed in the official store, and anything not listed means contacting support directly and hoping it can be sourced, which is a real risk on a machine with reported hardware issues and mixed long-term durability, where some owners report component wear over time. The counterweight is the ecosystem. It is semi-open, built on Klipper with third-party slicers accepted, so the machine is not locked to one vendor's software, and community wikis and resources carry a lot of the troubleshooting load. Firmware is actively maintained as of now. But if you are buying this to run as a business tool, weigh the thin official parts channel and the reactive support against the lifecycle risk before you commit to it for a long project.

Wrong or outdated? Report a data error

Keep exploring

From Elegoo

Alternative

New & upcoming